Compared with other years
NHTSA ODI complaints by model year
Registered new in Europe in 2011
2,662 new Hyundai Veloster cars were registered in the EU, Norway and Iceland in 2011; the largest markets were Germany (729), France (463), Italy (303).
- Average mass
- 1,291 kg
- Average power
- 103 kW
- Fuel type recorded
- Petrol 100%
European Environment Agency, CO₂ emissions from new passenger cars · averages weighted by registrations; CO₂ is the type-approval value; fuel type as recorded at registration, where many non-plug-in hybrids appear as petrol · re-use permitted with acknowledgement
In the Netherlands
164 first registered in 2011 are on Dutch roads; 35% arrived later as imports. Median list price when new: €29,995.
87.8%had an APK defect recorded since June 2022
93.5%logical odometer history
3.0%with a recall still open
Most common APK defects
- Bandenspanning niet op juiste waarde92
- Band onvoldoende profiel56
- Band beschadigd54
- Kentekenplaatverlichting werkt niet (goed) / ontbreekt42
- Stuurkogel te veel speling35
- Dimlicht onjuist afgesteld33
- Band(en) aanwezig met een profieldiepte van 1,6 t/m 2,5 mm31
- Waarschuwingsinrichting controlesysteem bandenspanning geeft30
Colours
Black 37%White 19%Red 19%Grey 13%Blue 5%
RDW Open Data: registered vehicles and APK defects (CC0) · defect descriptions in the RDW's Dutch wording
In the United Kingdom
12 cars built in 2011 were licensed for the road at the end of 2025, and 1 more were declared off the road (SORN).
12licensed, end of 2025
92%of those still registered are on the road
Department for Transport and DVLA, vehicle licensing statistics (table VEH0124, year of manufacture) · Open Government Licence v3.0
In Finland
23 of these cars first registered in 2011 were in use in Finland on 30 Jun 2026, with an average of 163,000 km on the odometer at their last inspection.
Traficom (Finnish Transport and Communications Agency), open data on vehicles in use · CC BY 4.0
In New Zealand
2 2011 cars are on the New Zealand register; 50% arrived as used imports, 50% were sold new in New Zealand.
NZ Transport Agency Waka Kotahi, Motor Vehicle Register (March 2026) · CC BY 4.0
Recalls
No recall campaigns cover the 2011 Hyundai Veloster.
Whether a recall was fixed on a particular car is known only to the manufacturer: check the VIN at nhtsa.gov/recalls.
NHTSA recalls · summaries in NHTSA's own words
Service bulletins
What Hyundai told its dealers about the 2011 Hyundai Veloster: known faults, fixes and updates.
| Bulletin | Summary |
|---|---|
| 10251285 | This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades. |
| 10247189 | This bulletin provides important checkpoint guidelines when performing engine oil and filter change services. |
| 10235566 | Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint. |
| 10230904 | This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation. |
| 10217258 | Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) established a threshold for correcting load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard. |
| 10217251 | Follow the guidelines outlined in this bulletin to inspect and clean or replace certain components of the engine intake system accordingly during engine short block or sub-assembly replacement. |
| 10190044 | This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps. |
| 10190038 | This bulletin provides best practice recommendations when performing brake service procedures. |
| 10189989 | This bulletin provides the inspection procedure and repair guidelines for certain vehicles listed below. |
| 10183963 | This bulletin describes the procedure to inspect and identify fluid which may appear around the brake caliper area. |
| 10183960 | This bulletin provides tire vibration service procedures, including how to optimize vehicle vibration performance. For all wheel/tire balance claims, the Tire Balance Data Sheet must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin. |
| 10178175 | This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation. |
| 10176182 | This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance. |
| 10176178 | This bulletin describes the general guidelines to help disinfect and protect vehicle exterior/interior surfaces using recommended safe chemical products. |
| 10174808 | This bulletin provides information on identifying dealer stock vehicles with either: A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. A 30 Day alert - vehicle has not started and reported an SOC in 30 days. |
| 10174807 | The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions: |
| 10173546 | This bulletin describes the general guidelines to disinfect and protect vehicle interior surfaces using certain safe chemical products. |
| 10173543 | This bulletin describes the procedure to apply grease to the coupling lever of a door latch that has difficulty opening. |
| 10172142 | This bulletin describes the requirements for all wheel alignment and/or vehicle tracking claims and best practices when diagnosing and conducting alignment-related repairs for all models and model years. |
| 10170883 | This bulletin provides guidelines to inspect the USB, head unit, and multi-box for common connection conditions. 2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port. |
| 10169370 | The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to en |
| 10167253 | This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number. |
| 10160098 | This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten. |
| 10140446 | On some Elantra (MD/UD), Elantra GT (GD) and Veloster (FS) vehicles, a noise may develop in the steering rack. This bulletin does not address any steering function related concerns. This bulletin provides information on replacement of the steering rack support yoke assembly. |
| 10117922 | Hyundai has launched a service campaign to inspect and if needed, repair the evaporative emissions canister and bracket on certain model year 2011? 2015 Hyundai Sonata Hybrid and 2012 ? 2016 Veloster vehicles. This campaign affects such vehicles registered in and operated in Alaska, Connecticut, Delaware, Illinois, Indiana, Iowa, Kansas, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, Nebraska, New Hampshire, New Jersey, New York, North Dakota, Ohio, Pennsylvania, Rhode Island, South Dakota, Utah, Vermont, West Virginia, and Wisconsin, and the District of Columbia. Re |
NHTSA manufacturer communications (public domain)