Isuzu Rodeo

Isuzu Manufacturing Services of America, Inc (Isuzu) is recalling certain model year 2003-2004 Rodeo and Axiom, and 2003 Rodeo Sport vehicles that were originally sold in, or are currently registered in, Maine, New Hampshire, Vermont, Massachusetts, Rhode Island, Connecticut, New York, New Jersey, Pennsylvania, Delaware, Maryland, the District of Columbia, West Virginia, Ohio, Indiana, Michigan, Illinois, Wisconsin, Minnesota, Iowa, Kentucky and Missouri. These vehicles may experience excessive corrosion near the forward mounting point bracket for the left or right rear suspension lower link.

ISUZU IS RECALLING CERTAIN MODEL YEAR 1998-2002 ISUZU RODEO AND MODEL YEAR 2002 ISUZU AXIOM VEHICLES, AND HONDA IS RECALLING CERTAIN 1998-2002 HONDA PASSPORT VEHICLES, THAT WERE ORIGINALLY SOLD, OR ARE CURRENTLY REGISTERED, IN THE STATES OF MAINE, NEW HAMPSHIRE, VERMONT, MASSACHUSETTS, RHODE ISLAND, CONNECTICUT, NEW YORK, NEW JERSEY, PENNSYLVANIA, DELAWARE, MARYLAND, THE DISTRICT OF COLUMBIA, WEST VIRGINIA, OHIO, INDIANA, MICHIGAN, ILLINOIS, WISCONSIN, MINNESOTA, IOWA, MISSOURI, AND KENTUCKY. VEHICLES THAT HAVE EXPERIENCED SUSTAINED EXPOSURE TO HIGHLY CORROSIVE MATERIALS USED IN SOME JURISDICTIONS FOR ROAD DEICING PURPOSES MAY EXPERIENCE EXCESSIVE CORROSION IN THE VICINITY OF THE FORWARD MOUNTING POINT BRACKET FOR THE LEFT OR RIGHT REAR SUSPENSION LOWER LINK PRIOR TO THE TIME THAT SUCH CORROSION WOULD NORMALLY BE EXPECTED.

CERTAIN SPORT UTILITY VEHICLES THAT HAVE BEEN EXPOSED TO FUEL CONTAMINATED WITH SILICON MAY DEVELOP SMALL PIN HOLES IN THE FUEL PUMP FEED PORT. SILICON HAS BEEN IDENTIFIED IN THE FUEL SYSTEMS OF AFFECTED VEHICLES AND IN CERTAIN FUEL AVAILABLE IN THE REGION OF TYLER, TEXAS. THIS RECALL WILL BE LAUNCHED FOR VEHICLES REGISTERED IN TEXAS AND THE FOUR SURROUNDING STATES: OKLAHOMA, ARKANSAS, NEW MEXICO AND LOUISIANA.

CERTAIN SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 101, "CONTROLS AND DISPLAYS." THE BRAKE WARNING LAMP WOULD NOT ILLUMINATE IN THE EVENT OF DECREASED BRAKE FLUID VOLUME.

ON CERTAIN SPORT UTILITY VEHICLES AND PICKUP TRUCKS, THE LATCH PLATE USED IN THE SEAT BELT BUCKLE WAS NOT MANUFACTURED ACCORDING TO DESIGN DIMENSIONS. IF THE SEAT BELT TONGUE IS INSERTED SLOWLY AT AN ANGLE INTO THE BUCKLE, THERE IS A POSSIBILITY OF PARTIAL ENGAGEMENT.

ON CERTAIN SPORT UTILITY VEHICLES, THE PASSENGER-SIDE AIR BAG INFLATOR MODULES WERE MANUFACTURED AND SHIPPED WITHOUT A NECESSARY COMPONENT KNOWN AS A CHECK VALVE PIN.

VEHICLE DESCRIPTION: CERTAIN SPORT UTILITY VEHICLES WERE BUILT WITH THE INFLATORS IN THE PASSENGER SIDE AIR BAG MODULES HAVING THE WRONG AMOUNT OF GENERANT.

VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. DURING THE MANUFACTURE OF CERTAIN FUEL RETURN HOSES, INCORRECT RUBBER MATERIAL FOR THE OUTER LAYER WAS USED.

VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. THESE VEHICLES FAIL TO COMPLY WITH THE PERFORMANCE REQUIREMENTS OF FMVSS NO. 201, "OCCUPANT PROTECTION IN INTERIOR IMPACT."

VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. PAINT WAS APPLIED UNEVENLY ON THE REAR AXLES, RESULTING IN INSUFFICIENT PAINT HARDNESS. SHOULD THIS OCCUR ON THE SURFACE THAT CONTACTS THE REAR AXLE LOWER LINK BRACKET BOLT HEAD AND/OR NUT, THE NUT MAY LOOSEN.

VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. A GROUND CONNECTION TERMINAL WAS NOT PROPERLY CRIMPED IN THE SUPPLIER'S ENGINE WIRING HARNESS MANUFACTURING LINE. THIS IMPROPER CRIMPING PROCESS CAN LEAVE AN IMPRESSION ON THE TERMINAL THAT WILL EVENTUALLY CAUSE A STRESS FRACTURE. S

VEHICLE DESCRIPTION: MULTI-PURPOSE PASSENGER VEHICLES EQUIPPED WITH A DRIVER'S SIDE OPTIONAL EQUIPMENT RUBBER FLOOR MAT. REPEATED MOVEMENT OF THE DRIVER'S FEET AND ACTUATION OF THE ACCELERATOR PEDAL CAN RESULT IN A SHIFTING OF THE MAT'S POSITION. THIS SHIFTING CAN CAUSE AN INTERFERENCE WITH THE ACCELERATOR PEDAL.