Problems owners report
Complaints filed with NHTSA about the 2008 Hyundai Entourage, by the system named in each complaint. One complaint can name several.
- Structure24
- Electrical system13
- Suspension11
- Latches/locks/linkages8
- Service brakes8
- Unknown or other6
- Engine5
- Electronic stability control (esc)4
- Engine and engine cooling4
- Steering4
NHTSA ODI complaints (public domain) · updated 23 Oct 2026 · 1 injuries and 0 deaths reported
Compared with other years
NHTSA ODI complaints by model year
Fatal crashes in the US
From 2020 to 2023, 5 2008 Entourage vehicles were involved in crashes on US public roads in which someone died; 1 person died inside them. This is a count, not a crash rate: it grows with the number of cars on the road.
NHTSA Fatality Analysis Reporting System (FARS), crash years 2020–2023 (public domain)
New York safety inspections
At its first New York inspection the 2008 Hyundai Entourage failed the safety check 2.72% of the time — 10% more often than the average 2008 passenger car (2.48%). Median odometer at inspection: 140,037 miles.
NY DMV Vehicle Inspections (vezn-fmmk), initial inspections since Aug 2021 · how we count
Fuel consumption
Official Canadian test results for 1 variant: combined 12.8 L/100 km (about 18 mpg US), CO₂ 294 g/km.
| Variant | City | Highway | Combined |
|---|---|---|---|
| Entourage · Minivan · Regular gasoline | 14.8 | 10.4 | 12.8 |
Litres per 100 km. Natural Resources Canada, Fuel consumption ratings (open.canada.ca) · Open Government Licence – Canada
Recalls in Canada
4 Transport Canada recalls for the 2008 Hyundai Entourage.
| 2020045 7 Feb 2020 | Brakes Issue: On certain vehicles equipped with an anti-lock brake system (ABS), moisture can enter the ABS control module and cause a short circuit. Safety Risk… |
| 2016596 28 Nov 2016 | Structure On certain vehicles, the secondary hood latch could corrode, and may result in the mechanical binding of the latch. This could cause the secondary hood latch t… |
| 2013389 7 Nov 2013 | Suspension On certain vehicles, road salt can corrode the front control arms, which may ultimately lead to control arm failure. This could result in a loss of vehicle cont… |
| 2013325 25 Sept 2013 | Electrical On certain vehicles, the stop lamp switch may fail and cause intermittent operation of the brake lights. Failure of the brake lights to illuminate when the brak… |
Transport Canada Vehicle Recalls Database · Contains information licensed under the Open Government Licence – Canada
Recalls
Hyundai Motor America (Hyundai) is recalling certain 2007-2010 Elantra and 2009-2011 Elantra Touring vehicles. On February 21, 2020 Hyundai expanded the recall to include 46,425 model year 2007-2008 Entourage and 2007 Santa Fe vehicles. Moisture may enter the Anti-lock Brake (ABS) Module and result in an electrical short.
Hyundai Motor America (Hyundai) is recalling certain model year 2007-2008 Entourage vehicles manufactured February 16, 2006, to June 30, 2008. In the affected vehicles, the secondary hood latch may corrode and bind and remain in the unlatched position when the hood is closed.
Hyundai America Technical Center, Inc. (Hyundai) is recalling certain model year 2007-2008 Hyundai Entourage vehicles manufactured from February 16, 2006, through June 30, 2008 and sold in, or currently registered in, Massachusetts, Maryland, Michigan, New Hampshire, New York, Pennsylvania, Vermont, Wisconsin, Connecticut, Delaware, Iowa, Illinois, Indiana, Maine, Minnesota, Missouri, New Jersey, Ohio, Rhode Island, West Virginia and the District of Columbia. In the affected vehicles, the front lower control arms may fracture due to corrosion resulting from exposure to road salt and water.
Hyundai Motor Company (Hyundai) is recalling certain model year 2006-2009 Accent, model year 2007-2011 Azera, Sonata and Sante Fe,2006-2011 Tucson, 2009-2011 Elantra Touring, 2007-2010 Elantra, 2008-2011 Veracruz, 2009-2011 Genesis, 2010-2011 Genesis Coupe, 2007-2008 Entourage, and 2006-2008 Tiburon vehicles. Originally, in April 2013, Hyundai recalled 1,059,824 model year 2007-2009 Accent and Tucson, model year 2007-2010 Elantra, model year 2007-2011 Santa Fe, model year 2008-2009 Veracruz, model year 2010-2011 Genesis Coupe, and model year 2011 Sonata vehicles. In September 2013, Hyundai informed the agency that it was adding more vehicles to this campaign, representing an additional 652,512 units. The total number of vehicles being recalled is now 1,712,336. In the affected vehicles, the stop lamp switch may malfunction. A malfunctioning stop lamp switch may cause the brake lights to not illuminate when the brake pedal is depressed or may cause an inability to deactivate the cruise control by depressing the brake pedal. Additionally, a malfunctioning stop lamp switch may also result in intermittent operation of the push-button start feature, affect the operation of the brake transmission shift interlock feature, preventing the shifter from being moved out of the PARK position and cause the Electronic Stability Control (ESC) malfunction light to illuminate.
Whether a recall was fixed on a particular car is known only to the manufacturer: check the VIN at nhtsa.gov/recalls.
NHTSA recalls · summaries in NHTSA's own words
Service bulletins
What Hyundai told its dealers about the 2008 Hyundai Entourage: known faults, fixes and updates.
| Bulletin | Summary |
|---|---|
| 10251285 | This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades. |
| 10247189 | This bulletin provides important checkpoint guidelines when performing engine oil and filter change services. |
| 10235566 | Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint. |
| 10230904 | This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation. |
| 10217258 | Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) established a threshold for correcting load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard. |
| 10217251 | Follow the guidelines outlined in this bulletin to inspect and clean or replace certain components of the engine intake system accordingly during engine short block or sub-assembly replacement. |
| 10196546 | Hyundai approves only the ATF, DCT gear oil and IVT gear oil specified in the vehicles owners manual. Use of other ATF may result in improper shift quality or other drivability conditions. Use of other DCT and IVT gear oil may result in reduced durability. Hyundai does not approve the use of any aftermarket ATF or gear oil additives. |
| 10190044 | This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps. |
| 10190038 | This bulletin provides best practice recommendations when performing brake service procedures. |
| 10189989 | This bulletin provides the inspection procedure and repair guidelines for certain vehicles listed below. |
| 10183963 | This bulletin describes the procedure to inspect and identify fluid which may appear around the brake caliper area. |
| 10183960 | This bulletin provides tire vibration service procedures, including how to optimize vehicle vibration performance. For all wheel/tire balance claims, the Tire Balance Data Sheet must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin. |
| 10178175 | This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation. |
| 10177599 | These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected. |
| 10177598 | These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected. |
| 10176182 | This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance. |
| 10176178 | This bulletin describes the general guidelines to help disinfect and protect vehicle exterior/interior surfaces using recommended safe chemical products. |
| 10174808 | This bulletin provides information on identifying dealer stock vehicles with either: A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. A 30 Day alert - vehicle has not started and reported an SOC in 30 days. |
| 10174807 | The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions: |
| 10173546 | This bulletin describes the general guidelines to disinfect and protect vehicle interior surfaces using certain safe chemical products. |
| 10172142 | This bulletin describes the requirements for all wheel alignment and/or vehicle tracking claims and best practices when diagnosing and conducting alignment-related repairs for all models and model years. |
| 10170883 | This bulletin provides guidelines to inspect the USB, head unit, and multi-box for common connection conditions. 2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port. |
| 10169370 | The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to en |
| 10167253 | This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number. |
| 10160098 | This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten. |
NHTSA manufacturer communications (public domain)