Problems owners report
Complaints filed with NHTSA about the 2017 Mercedes-Benz GLC300, by the system named in each complaint. One complaint can name several.
- Engine37
- Electrical system15
- Fuel/propulsion system14
- Unknown or other12
- Air bags11
- Seat belts8
- Power train7
- Visibility6
- Service brakes4
- Forward collision avoidance4
NHTSA ODI complaints (public domain) · updated 23 Oct 2026 · 2 injuries and 0 deaths reported
Recalls
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014-2020 C-Class, CLA, GLA, S-Class, GLC, and GLE vehicles. Please refer to MBUSA's recall report for specific vehicle details. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair, allowing the front panel to detach from the vehicle.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2020 C300 Coupe, C43 Coupe AMG, C43 AMG, 2015-2020 C300, GLA250, 2016-2018 C350e, CLA45 Coupe AMG, 2015 C400, S65 AMG, 2015-2019 C63 AMG, 2016 C450, 2015-2016 GLA45 AMG, S600, 2016-2020 GLC300, 2017-2019 GLC43 AMG, GLE43 Coupe AMG, 2014-2019 CLA250 Coupe, 2014-2015 CLA45 AMG, 2018 GLC63 AMG, 2014-2017 S550, 2018-2020 S450, 2016-2019 GLE63 Coupe AMG, 2016 GLE450 Coupe, 2014-2020 S63 AMG, 2018-2019 S560, and 2019 GLC350e vehicles equipped with a panoramic sunroof. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2019 C300, E300, 2018-2020 CLA250, 2020 CLS450, AMG E53, AMG GT53, GLE450, 2018 AMG E63, AMG GTA, 2017-2020 GLA250, GLC300, 2019 GLC350, AMG GLC43, 2017-2018 GLE350, 2019 AMG GLC 43, GLC350, GLE400, 2017 GLS450, S550, C300 Cabrio, and 2018-2019 S560 vehicles. On June 18, 2021, an additional 9 vehicles were added, including certain 2021 GLA250, GLC300, 2018 S450, E400, and 2017 CLA250 vehicles. The communication module might have been inadvertently deactivated during a service visit, which could have disabled the Emergency Call (eCall) function.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication module may fail to communicate the correct vehicle location for the emergency call system (eCall) in the event of a crash.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2016-2018 Mercedes-Benz GLC300 and GLC300 4Matic, 2018 GLC350e and GLC63 AMG 4Matic and 2017-2018 GLC43 AMG 4Matic vehicles. The seat belt latch plates (the parts that insert into the buckles) for the outboard rear seats may retract into the interior paneling, preventing the occupants from being able to use the seat belts.
Mercedes Benz USA LLC (MBUSA) is recalling certain 2017-2018 GLC43 AMG, 2016-2018 GLC300 4Matic, 2016-2018 GLC300, 2018 GLC63 AMG 4Matic, and 2018 GLC350e 4Matic vehicles. The seat belt latch plates (the parts that insert into the buckles) for the outboard rear seats may retract into the interior paneling, preventing the occupants from being able to use the seat belts.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016-2017 GLC300, GLC300 4MATIC and GLC43 4MATIC vehicles. These vehicles may have misadjusted headlights, possibly resulting in the low beam headlights insufficiently illuminating the roadway. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2018 GLC300, GLC300 4Matic, and GLC43 AMG vehicles. The fixed panoramic sun roof frontal and side plastic panels may have insufficient bonding, allowing the panels to separate during vehicle operation.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec, GLK350, GLK350 4Matic, 2016-2017 C350e, C43 AMG, 2015 C400 4Matic, 2016-2018 C63 AMG, GLC300, GLC300 4Matic, 2017-2018 C300 Coupe, C300 4Matic Coupe, C43 AMG, C63 AMG Coupe, C63S AMG Coupe, C300 Cabriolet, C300 4Matic Cabriolet, C43 AMG Cabriolet, C63 AMG Cabriolet, C63S AMG Cabriolet, GLC300 4Matic Coupe, GLC43 AMG, GLC43 AMG Coupe, 2014 E350 Coupe, E350 4Matic Coupe, E350 Cabriolet, E400 Hybrid, 2015-2017 E400 Coupe, E400 4Matic Coupe, E400 Cabriolet, 2014-2017 E550 Coupe, E550 Cabriolet, B250e, 2014-2016 E250 BlueTec, E63 AMG 4Matic Wagon, 2012-2013 E350 BlueTec, 2012-2016 E350, E350 4Matic, 2015-2016 E400, E400 4Matic, 2012 E63 AMG, 2014-2015 E250 4Matic BlueTec, 2013-2016 E350 Wagon, 2017 GLC300d 4Matic, and 2018 GLC350e 4Matic. The driver's air bag may unexpectedly deploy due to insufficient grounding of the steering components if an electrostatic discharge occurs and the air bag clockspring is broken.
Mercedes-Benz USA, LLC. (MBUSA) is recalling one 2017 C43 AMG, one E300 4Matic sedan, one GLC300, and one E43 AMG 4Matic sedan. These vehicles have electrical power steering control units with improperly welded contact pins.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017 C300, C300 4Matic, C300 Coupe, C300 Coupe 4Matic, C43 AMG, C43 AMG Coupe, C43 AMG Cabrio, C63 AMG, C63 AMG Coupe, C63S AMG, C63S AMG Coupe, C63S Cabrio, GLC300, GLC300 4Matic, GLC43 AMG, S550, S550 4Matic, S550e, S600, S63 AMG 4Matic, S65, Mercedes-Maybach S550 4Matic, and Mercedes-Maybach S600 vehicles. The affected vehicles have front seat seatbelt pretensioners that may not function properly in the event of a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection," and 209, "Seat Belt Assemblies."
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2015-2017 C300 4Matic, C300, CLA250, CLA250 4Matic and CLA45 AMG vehicles, 2017 C300 4Matic Cabrio, C300 4Matic Coupe, C300 Cabrio, C300 Coupe, E300, E300 4Matic, E400 4Matic Wagon, E43 AMG 4Matic, GLA250, GLA250 4Matic and GLC300 4Matic Coupe vehicles and 2016 C350e and GLC300 vehicles and 2016-2017 C450 4Matic AMG Sport and GLC300 4Matic vehicles. In the event that the engine or transmission cannot turn over, the starting current limiter may overheat from the repeated attempts of the starter motor attempting to start the vehicle.
Whether a recall was fixed on a particular car is known only to the manufacturer: check the VIN at nhtsa.gov/recalls.
NHTSA recalls · summaries in NHTSA's own words
Service bulletins
What Mercedes-Benz told its dealers about the 2017 Mercedes-Benz GLC300: known faults, fixes and updates.
| Bulletin | Summary |
|---|---|
| 11010907 | Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes i |
| 11010818 | Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established |
| 11010755 | Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see |
| 11010644 | Complaint Paint damage on door paneling in area of door handle (see picture 1). Cause Possible tolerance complaint regarding the door handle Remedy 1. Paint the affected area of the door paneling using the spot repair procedure in accordance with the manufacturer's specifications. 2. Replace door handle, ensuring that the door handle bearing bracket is installed correctly (see picture 2). Note: The optimized door handles are marked as shown in the illustration (see picture 3). |
| 11010494 | Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the ve |
| 11010455 | Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test |
| 11009122 | Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer l |
| 11008712 | Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connecti |
| 11008091 | Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protrudin |
| 11008064 | In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles. |
| 11007974 | Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for cor |
| 11007790 | Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside |
| 11007753 | Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an eng |
| 11007728 | Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Al |
| 11006658 | Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control |
| 11005344 | Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact o |
| 11005331 | Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test |
| 11005294 | Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the ve |
| 11000598 | Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limi |
| 10253722 | Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Model year 2015-2018 Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for model year 2015-2018 vehicles. Model year 2019 Perform software update for N3/10 Engin |
| 10252835 | Always use the latest XENTRY Diagnosis software release with all available add-ons. Make sure to follow the operation steps exactly as described in XENTRY Diagnosis. Use a battery charger to ensure sufficient power supply of the vehicle on-board electrical system battery (greater than 12.5 V). If XENTRY Diagnosis is already connected to the vehicle, start with operation step 2. If two or more software updates or SCN codings are performed during one workshop visit, operation items 02-4762 and 02-5058 may be invoiced only once for each workshop order. Work procedure 1. Connect X |
| 10251356 | The radio station favorites list is no longer present after bus idle Saving process during download Perform software update in control unit HU6 in the head unit (A26/17) to version E871.1 (A 247 904 53 00). |
| 10249726 | Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background |
| 10248162 | Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material! |
| 10244837 | The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If |
NHTSA manufacturer communications (public domain)
NHTSA investigations
Desiccated Air Bag Inflator Rupture
Front Roof Panel Detachment
NHTSA Office of Defects Investigation