Problems owners report
Complaints filed with NHTSA about the 2024 BMW i5, by the system named in each complaint. One complaint can name several.
- Electrical system5
- Electronic stability control (esc)5
- Service brakes, hydraulic4
- Service brakes4
- Forward collision avoidance3
- Unknown or other3
- Back over prevention2
- Lane departure2
- Steering2
- Engine1
NHTSA ODI complaints (public domain) · updated 23 Oct 2026 · 0 injuries and 0 deaths reported
New York safety inspections
At its first New York inspection the 2024 BMW i5 failed the safety check 0.24% of the time — 55% less often than the average 2024 passenger car (0.53%). Median odometer at inspection: 4,830 miles.
NY DMV Vehicle Inspections (vezn-fmmk), initial inspections since Aug 2021 · how we count
In the Netherlands
1,566 first registered in 2024 are on Dutch roads; 11% arrived later as imports. Median list price when new: €90,167.
Most common APK defects
- Dimlicht onjuist afgesteld8
- Bandenspanning niet op juiste waarde8
- Stuur- of fuseekogel met slijtage kleiner of gelijk 1,0 mm4
- Stuurkogel te veel speling2
- Band beschadigd2
- Band(en) aanwezig met een profieldiepte van 1,6 t/m 2,5 mm1
Colours
RDW Open Data: registered vehicles and APK defects (CC0) · defect descriptions in the RDW's Dutch wording
In the United Kingdom
3,743 cars built in 2024 were licensed for the road at the end of 2025, and 24 more were declared off the road (SORN).
Department for Transport and DVLA, vehicle licensing statistics (table VEH0124, year of manufacture) · Open Government Licence v3.0
In Finland
406 of these cars first registered in 2024 were in use in Finland on 30 Jun 2026, with an average of 26,000 km on the odometer at their last inspection.
Traficom (Finnish Transport and Communications Agency), open data on vehicles in use · CC BY 4.0
Recalls in Canada
4 Transport Canada recalls for the 2024 BMW i5.
| 2025320 13 Jun 2025 | High Voltage Issue: On certain vehicles, a problem with the electric drive motor software could cause the vehicle to enter a fail-safe mode. If this happens, there could b… |
| 2024544 15 Aug 2024 | Label Issue: On certain vehicles, the tire and loading information label does not list that there is no spare tire in both official languages. The label reads as "N… |
| 2024456 12 Aug 2024 | Brakes Issue: On certain vehicles, a problem with the integrated brake system could cause reduced power brake assist. As a result, there may be reduced braking and t… |
| 2023561 18 Oct 2023 | Electrical Issue: On certain vehicles, the steering wheel hands-on detection system may not detect when the driver removes their hands from the steering wheel. If the dr… |
Transport Canada Vehicle Recalls Database · Contains information licensed under the Open Government Licence – Canada
Recalls
BMW of North America, LLC (BMW) is recalling certain 2025 Mini Cooper S, Mini Countryman S All4, X2, 2024 Rolls-Royce Spectre, 2023-2025 i7, 7 Series, X7, 2024-2025 i5, 5 Series, 2023-2024 XM, X1, 2024-2025 X6, and X5 vehicles. The integrated brake (IB) system may malfunction and result in a loss of power brake assist or cause the Antilock Brake (ABS) and Dynamic Stability Control (DSC) systems to not function properly.
BMW of North America, LLC (BMW) is recalling certain 2022-2025 i4, 2022-2024 IX, 2023-2024 I7, and 2024 I5 vehicles. The electric drive motor software may shut down the high-voltage system, causing a loss of drive power.
BMW of North America (BMW) is recalling certain 2023-2024 X1, 2024-2025 X5, 2025 X6, 2023-2025 X7, 740i, 760i, 2024 XM, 530i, 540i, i7, 750e, X2, 2024-2025 i5, 2024 Rolls Royce Spectre, 2025 MINI Countryman S ALL4, JCW Countryman ALL4, and 2025 MINI Hardtop 2 Door (Cooper, Cooper S) vehicles. Please refer to the recall report for the complete list of models. The welds in the servomotor of the integrated brake control module may break, causing a loss of power brake assist and rear brake function. In addition, the Antilock Brake System (ABS) and Dynamic Stability Control (DSC) system may not function.
BMW of North America, LLC (BMW) is recalling certain 2024 i4 xDrive40, i4 M50 and i5 eDrive40 vehicles. The high-voltage battery module may contain insufficient weld seams, which can result in the battery overheating.
BMW of North America, LLC. (BMW) is recalling certain 2023-2025 BMW, MINI, and Rolls-Royce vehicles. Please see the recall report for a complete list of models and model years. The integrated brake (IB) system may malfunction and result in a loss of power brake assist or cause the Antilock Brake (ABS) and Dynamic Stability Control (DSC) systems to not function properly.
BMW of North America, LLC (BMW) is recalling certain 2024 i5 eDrive40 and i5 M60 vehicles. During vehicle start-up, the artificial sound generator control unit may experience a fault and fail to generate the external pedestrian warning sound. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 141, "Minimum Sound Requirements for Hybrid and Electric Vehicles."
BMW of North America, LLC (BMW) is recalling certain 2023-2024 740i, 740i xDrive, 760i xDrive, i7 eDrive50, i7 xDrive60, i7 M70, 2024 750e xDrive, 530i, 530i xDrive, i5 eDrive40, and i5 M60 vehicles. The ground connection to the steering wheel may not have been attached correctly, resulting in an inoperative hands-on detection system.
Whether a recall was fixed on a particular car is known only to the manufacturer: check the VIN at nhtsa.gov/recalls.
NHTSA recalls · summaries in NHTSA's own words
Service bulletins
What BMW told its dealers about the 2024 BMW i5: known faults, fixes and updates.
| Bulletin | Summary |
|---|---|
| 11012093 | Quality checks have determined that the coolant changeover valve may develop a coolant leak undervery low outside temperatures (significantly lower than 32 F (0 C)). |
| 11012080 | The customer states there is a Drivetrain Malfunction message displayed in the instrument cluster. In addition, the following fault memory entries are saved in the CCU (Combined Charging Unit) 0317F2 - High-voltage system, insulation fault detected: when switch contactors are closed. 0317F1 - High-voltage system, insulation resistance below warning threshold: when switch contactors are closed. The fault memory entries (isolation faults) can occur both individually and in combination and must be traced back to the eDrive motor based on the ISTA test procedure. If ISTA test procedure lists possi |
| 11008992 | Improved diagnostic software for the brake system. |
| 11008114 | A manufacturing defect in high-voltage cells of the high-voltage battery can result in electrolyte leakage which might result in a conductive connection with surrounding components. Depending on the contact resistance, a yellow or red Check Control message will then be displayed; it is permitted for you to continue driving, but this will result in a charging interruption during charging. |
| 11006742 | Replace Cell Modules |
| 11006734 | Customer states they started to receive Check Control messages for the drivers seat at the end of eachdriving cycle: One or more of the following check control messages (CCM) were present at that time: CCM 434 Seat calibration required. CCM 108 Driver restraint system. Eventually multiple restarts after they first noticed the CCM the seat stopped functioning, the air bag warninglamp illuminated in the instrument cluster, and they received a new Check Control message: CCM 97 Restraint system. There are now 6 DTC faults stored: ACSM6 Air Bag module 930D86 - Function restraint system driver restr |
| 11005450 | The seat initialization and memory has been lost; Or Repeat failure of seat initialization after completing the test module via ISTA. One or both of the following check control messages (CCM) may be present: CCM 108 Driver restraint system CCM 109 Passenger restraint system |
| 11005236 | Quality checks have determined that the coolant changeover valve may develop a coolant leak under very low outside temperatures (significantly lower than 32 F (0 C)). |
| 11005233 | When driving over rough surfaces, a low-frequency rattling noise can be heard inside the vehicle's cabin.The noise typically sounds as though it is coming from the front right footwell area. |
| 11005226 | While driving at low speeds (15-40 mph) on flat road surfaces, a knocking noise from the front axle may beheard during steering wheel movements. |
| 11002669 | A drumming noise is heard when the air conditioning system is operating. |
| 11000512 | Quality checks have determined that the coolant changeover valve may develop a coolant leak under very low outside temperatures (significantly lower than 32 F (0 C)). |
| 11000510 | DELIVERY STOP: COOLANT CHANGEOVER VALVE |
| 10253344 | There is coolant leaking from under the car Low heater output Possible Check Control message Drive, you can continue driving (ID49) Possible fault codes stored in these BEV vehicles: 224163 Electric auxiliary heater for the high-voltage battery unit: Undervoltage or internal communication fault 8049AA - Coolant level sensor, expansion tank: Coolant level low or short circuit to ground or line disconnection 80124F Electric auxiliary heater: Communication in electric auxiliary heater faulty 224F60 - Coolant level sensor, expansion tank: Coolant level low or short circuit to ground or |
| 10252133 | When the interior temperature of the vehicle is between 5 F (-15 C) and 23 F (-5 ), the defroster function is limited; and the interior doesnt heat up quickly enough. |
| 10252041 | 1. The center air vent on the left (a) is closed. All other air vents on the left side then only blow cold air intothe passenger area. OR 2. Both center (b) air vents are closed. All other air vents then only blow cold air into the passenger area. OR 3. The center air vent on the right (c) is closed. All other air vents on the right side then only blow cold airinto the passenger area. |
| 10252039 | This Informational Bulletin is intended as a guided work through process to address BEV/PHEV charging issues. The step-by-step guide will help walk you through the correct basic steps that should be followed when addressing and diagnosing battery electric vehicles (BEV) and plug in hybrid vehicles (PHEV) charging issues. |
| 10252032 | A squeaking sound is heard when folding either of the exterior mirrors assemblies in or out. |
| 10252029 | This Informational Bulletin is intended as a guided work-through process to address customer charging complaints. The step-by-step guide will help walk you through the basic procedure to test the charger/infrastructure when the vehicle does not charge, either at a: Home charger AC Level 1/Level 2 - Flexible Fast Charger/hard wired Wallbox, or a Public AC Level 2, or DC Level 3 - Fast Charging Station Note: All PHEV and BEV vehicles may be affected. |
| 10252015 | The seat initialization and memory has been lost; Or Repeat failure of seat initialization after completing the test module via ISTA. One or both of the following check control messages (CCM) may be present: CCM 108 Driver restraint system CCM 109 Passenger restraint system |
| 10250894 | When driving over rough surfaces, a low-frequency rattling noise can be heard inside the vehicle's cabin. The noise typically sounds as though it is coming from the front right footwell area. |
| 10250603 | A drumming noise is heard when the air conditioning system is operating. |
| 10250367 | The coolant changeover valve may develop a coolant leak when the outside temperatures go below 19F (-7C). The vehicles operating systems would also need to be at that same low temperature (example: being parked outside, overnight in low temperatures). |
| 10250365 | Gen 5 BEV/PHEV vehicles may set the Combined Charging Unit (CCU) in programming abort due to nocommunication to the HV charge socket electronics. |
| 10250361 | The customer states there is a Drivetrain Malfunction message displayed in the instrument cluster. In addition, the following fault memory entries are saved in the CCU (Combined Charging Unit) 0317F2 - High-voltage system, insulation fault detected: when switch contactors are closed. 0317F1 - High-voltage system, insulation resistance below warning threshold: when switch contactors are closed. The fault memory entries (isolation faults) can occur both individually and in combination and must be traced back to the eDrive motor based on the ISTA test procedure. If ISTA test procedure list |
NHTSA manufacturer communications (public domain)