Problems owners report
Complaints filed with NHTSA about the 2019 Mercedes-Benz E 300, by the system named in each complaint. One complaint can name several.
- Unknown or other9
- Seat belts7
- Engine3
- Electrical system3
- Air bags2
- Wheels2
- Lane departure2
- Fuel/propulsion system2
- Back over prevention2
- Steering1
NHTSA ODI complaints (public domain) · updated 23 Oct 2026 · 3 injuries and 0 deaths reported
Fuel consumption
Official Canadian test results for 1 variant: combined 9.7 L/100 km (about 24 mpg US), CO₂ 228 g/km.
| Variant | City | Highway | Combined |
|---|---|---|---|
| E 300 4MATIC · Mid-size · Premium gasoline | 11.0 | 8.1 | 9.7 |
Litres per 100 km. Natural Resources Canada, Fuel consumption ratings (open.canada.ca) · Open Government Licence – Canada
Recalls
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card software can cause a mobile network connection failure, disabling the emergency call (eCall) system.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2018-2021 CLA-Class, GLE/GLS-Class, A-Class, C-Class, E-Class, E-Class Coupe/Convertible, GLA/GLB-Class, GLC-Class, and CLS-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The rearview camera may not display the rearview image due to a software error. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019 AMG G63, C300, E300, G550, AMG GT63, AMG GT53, 2019-2020 A220, GLA250, GLC300, 2016 C300, 2020 AMG A35, AMG C43, AMG C63, CLA250, E350, E450, GLB250, GLE450, GLS450, GLS580, S560, and SL550 vehicles equipped with a gasoline engine. During the manufacturing process, particles may have been trapped between the fuel rail and injectors, which can cause a fuel leak.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2019 C300, E300, 2018-2020 CLA250, 2020 CLS450, AMG E53, AMG GT53, GLE450, 2018 AMG E63, AMG GTA, 2017-2020 GLA250, GLC300, 2019 GLC350, AMG GLC43, 2017-2018 GLE350, 2019 AMG GLC 43, GLC350, GLE400, 2017 GLS450, S550, C300 Cabrio, and 2018-2019 S560 vehicles. On June 18, 2021, an additional 9 vehicles were added, including certain 2021 GLA250, GLC300, 2018 S450, E400, and 2017 CLA250 vehicles. The communication module might have been inadvertently deactivated during a service visit, which could have disabled the Emergency Call (eCall) function.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication module may fail to communicate the correct vehicle location for the emergency call system (eCall) in the event of a crash.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2019 C300, C300 Coupe, CLS450, E450 Coupe and S450, 2017-2019 E300, 2018 E400 Coupe, E400 Stationwagon, and 2018-2019 S560 vehicles that have previously had the instrument cluster replaced. The software in the replaced instrument cluster may cause the seat belt warning system to not operate properly, only displaying a solid warning light if either the driver or passenger seat belt is unfastened, instead of a blinking light with an audible tone.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2018 E400 Wagon 4MATIC, E400 4MATIC, E43 AMG 4MATIC, 2018-2019 E63S AMG 4MATIC Wagon, E63 AMG 4MATIC Wagon, E300, E300 4MATIC, GLC63S Coupe AMG 4MATIC, 2019 CLS450, CLS450 4MATIC, CLS53 AMG 4MATIC, E450 Wagon, E53 AMG 4MATIC, GLC300, GLC63 AMG Coupe 4MATIC, G550 4MATIC, G63 AMG, GLC300 Coupe 4MATIC, GLC300 4MATIC, GLC350e 4MATIC, GLC43 AMG Coupe 4MATIC, GLC43 AMG 4MATIC, GLC63 AMG 4MATIC, GT63 AMG four-door 4MATIC, and GT63S AMG four-door 4MATIC vehicles. Although correctly fastened, the front seat belts may be inaccurately detected as being unfastened, which may cause the electric PRE-SAFE®-function and the pretensioner to be deactivated.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2019 C300 Cabrio, C300A Cabrio 4MATIC, C300 Coupe, C300 Coupe 4MATIC, C300, C300 4MATIC, C43 AMG Cabrio 4MATIC, C43 AMG Coupe 4MATIC, C43 AMG 4MATIC, C63 AMG Cabrio, C63S AMG Cabrio, C63 AMG Coupe, C63S AMG Coupe, C63 AMG, C63S AMG, CLS450, CLS450 4MATIC, CLS53 AMG 4MATIC, E300, E300 4MATIC, E450 Cabrio, E450 Cabrio 4MATIC, E450 Coupe, E450 Coupe 4MATIC, E450 Wagon 4MATIC, E450 4MATIC, E53 AMG Cabrio 4MATIC, E53 AMG Coupe 4MATIC, E53 AMG 4MATIC, E63S AMG 4MATIC, E63S AMG Wagon 4MATIC, S450, S450 4MATIC, S560 Cabrio, S560 Coupe 4MATIC, S560, S560 4MATIC, S560 4MATIC Maybach, S63 AMG Cabrio 4MATIC, S63 AMG Coupe 4MATIC, S63 AMG 4MATIC, S65 AMG Cabrio, S65 AMG, and AMG GT53 Coupe 4MATIC vehicles, and 2020 GLC300 Coupe 4MATIC, GLE350 4MATIC, and GLE450 4MATIC vehicles equipped with the Driver Assistance Package. A software error in the radar sensor control unit may impair the functionality of the Active Brake Assist.
Whether a recall was fixed on a particular car is known only to the manufacturer: check the VIN at nhtsa.gov/recalls.
NHTSA recalls · summaries in NHTSA's own words
Service bulletins
What Mercedes-Benz told its dealers about the 2019 Mercedes-Benz E 300: known faults, fixes and updates.
| Bulletin | Summary |
|---|---|
| 11010818 | Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established |
| 11010755 | Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see |
| 11010494 | Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the ve |
| 11010455 | Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test |
| 11009122 | Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer l |
| 11009025 | Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) 2018 - 2024 E-Class, S-Class & AMG GT (213, 217, 222, 223 and 290 platforms) vehicles, the low pressure fuel line does not meet current production specifications. Therefore, it is possible that accelerated aging in the area of connection could occur, resulting in a leak. A risk of fire can be ruled out. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will replace the braided hose of low-pressure fuel line and install a heat shield over the n |
| 11008880 | Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see |
| 11008873 | Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct instal |
| 11008712 | Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connecti |
| 11008323 | Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: O |
| 11008091 | Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protrudin |
| 11008056 | Complaint Check engine light on. Fault code P207273 - "Throttle actuator valve is blocked due to ice" stored. Engine may crank and not start. Fault code P210185 may also be stored. Cause Moisture freezing on throttle actuator during extreme low ambient temperatures. Remedy Update software of engine control module. Software increases throttle valve flapping after engine turned off to prevent moisture buildup. |
| 11007974 | Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for cor |
| 11007753 | Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an eng |
| 11007728 | Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Al |
| 11005344 | Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact o |
| 11005331 | Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test |
| 11005294 | Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the ve |
| 11005276 | Complaint Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy Model year 2018 C300 | Model year 2016-2018 GLC300 and E300 | ALL model year SLK/SLC300 and hybrid variants Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is av |
| 11003218 | Complaint Complaints about shift quality in vehicles of MODEL 205, 212 and 222 with TRANSMISSION 724.2. Cause If the shift adaptation is not performed as described under "Remedy", the adaptation values may not be saved correctly under certain circumstances. Remedy In vehicles of MODEL 205, 212 and 222 with TRANSMISSION 724.2, it must be ensured that the adaptation of the shifts is performed only as described below. Acceleration upshifts may only be adapted in transmission mode "S" Acceleration downshifts may only be adapted in transmission mode "S" Coast down shifts may only be adapted in t |
| 11000623 | Complaint Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy Model year 2015-2018 (non-hybrid), and ALL model year 172 and hybrid variants Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for hybrid and model y |
| 11000598 | Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limi |
| 10253722 | Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Model year 2015-2018 Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for model year 2015-2018 vehicles. Model year 2019 Perform software update for N3/10 Engin |
| 10253703 | This is to notify you of the Service Campaign OTA update for the MBUX system software in 750,313 Model Year (MY) MY19-24 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-24 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLA, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253, 167, 290 platform) vehicles, the MBUX system software does not cor |
| 10252777 | Tailgate opens unintentionally. Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. The recoding can be carried out as follows: 1. Add AO code O19 in VeDoc (O as in the letter "O" for Oscar, not the number "0"/zero) 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indic |
NHTSA manufacturer communications (public domain)