Mitsubishi Eclipse Spyder

Mitsubishi Motors North America, Inc. (MMNA) is recalling certain model year 2000-2005 Eclipse vehicles manufactured April 5, 1999, to December 17, 2004, 2001-2005 Eclipse Spyder vehicles manufactured January 19, 2000, to March 18, 2005, 2001-2005 Chrysler Sebring vehicles manufactured April 17, 2000, to February 21, 2005, and 2001-2005 Dodge Stratus vehicles manufactured April 17, 2000, to February 22, 2005. In the affected vehicles, the passenger side sun visor may be folded down in such a position that, if the passenger frontal air bag deploys, the passenger side sun visor may detach.

Mitsubishi Motors North America, Inc. (MMNA) is recalling certain model year 2006-2009 Eclipse vehicles manufactured April 20, 2005, to February 13, 2009, and 2007-2009 Eclipse Spyder vehicles manufactured December 23, 2005, to February 13, 2009. Due to corrosion inside the antil-lock brake system (ABS) unit, one or more of the internal valves may seize. In a braking event that uses the ABS, a seized valve would increase brake pedal travel and reduce braking ability.

MITSUBISHI IS RECALLING 45,988 MY 2005-2007 ENDEAVOR, GALANT, ECLIPSE COUPE, AND MY 2007 ECLIPSE SPYDER VEHICLES. THE BRACKET THAT IS THE ATTACHMENT POINT FOR THE LEFT REAR FUEL TANK MOUNTING STRAP MAY HAVE BEEN IMPROPERLY FORMED DURING A METAL STAMPING PROCESS. THE PROCESS MAY HAVE CAUSED THE METAL TO HAVE A SPLIT IN THE AREA WHERE THE BOLT THAT HOLDS ONE OF THE TWO FUEL TANK STRAPS TO THE UNDERSIDE OF THE VEHICLE IS LOCATED. IN THE EVENT THE FUEL TANK IS FULL AND THE VEHICLE IS SUBJECT TO A SEVERE COLLISION, THE BRACKET MAY BREAK AND ALLOW THE FUEL TANK TO DROP DOWN, POSSIBLY CAUSING A FUEL LEAK.

ON CERTAIN VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS, THE KEY LOCK CABLE WAS IMPROPERLY MANUFACTURED AND MAY NOT ALLOW THE CABLE END TO LOCK INTO THE FLOOR SHIFTER MECHANISM. THIS CAN RESULT IN THE INTERLOCK SYSTEM TO BECOME INOPERATIVE AND ALLOW THE IGNITION KEY TO BE REMOVED WITHOUT THE GEARSHIFT MECHANISM BEING PLACED IN THE PARK POSITION.

ON CERTAIN PASSENGER VEHICLES, THE METAL FORMING PART OF THE FRONT CROSSMEMBER MAY HAVE BEEN IMPROPERLY STAMPED RESULTING IN THE METAL BECOMING THINNER IN THE CROSS-SECTION THAN SPECIFIED. THIS COULD, OVER TIME, RESULT IN BREAKAGE OF THE CROSSMEMBER.

CERTAIN PASSENGER VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, 'OCCUPANT CRASH PROTECTION.' THE BILINGUAL ENGLISH/SPANISH REMOVABLE AIR BAG WARNING LABELS AFFIXED TO THE DASH AND TO THE SUNVISOR DO NOT MEET THE SIZE REQUIREMENTS OF THE STANDARD.

ON CERTAIN PASSENGER VEHICLES, THE FUEL RETURN LINE HOSE FITTING ON THE ELECTRIC FUEL PUMP MAY BE IMPROPERLY MOLDED.

ON CERTAIN PASSENGER VEHICLES, THE FUEL RETURN LINE HOSE FITTING ON THE ELECTRIC FUEL PUMP MAY BE RESTRICTED, CAUSING EXCESSIVE FUEL PRESSURE TO BUILD UP IN THE FUEL INJECTION SYSTEM. EXCESSIVE FUEL PRESSURE MAY RESULT IN A LEAK IN THE FUEL RETURN HOSE.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. A BULGE IN THE FUEL TANK CAUSED BY THE MANUFACTURING PROCESS RESULTED IN THINNING OF THE MATERIAL DURING A WELDING OPERATION, INCREASING THE RISK OF FUEL LEAKAGE.

VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS. A HOSE WAS MIS-MANUFACTURED AND COULD WEAKEN OVER TIME, WHICH COULD RESULT IN LEAKAGE OF THE AUTOMATIC TRANSMISSION FLUID.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. A NUMBER OF INCORRECT DRIVER SIDE SEAT MOUNTING BOLTS WERE INSTALLED INTO VEHICLES.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. IF THE RUBBER BOOTS ON THE LOWER LATERAL ARM BALL JOINTS OF THE FRONT SUSPENSION WERE DAMAGED DURING ASSEMBLY, DIRT AND WATER CAN INTRUDE. ALSO, MMC HAS ADDED THE POTENTIAL OF LEAKING MOISTURE, WHICH CAN CAUSE THE BALL STUD TO CORRODE.