Problems owners report
Complaints filed with NHTSA about the 2015 Mercedes-Benz C300, by the system named in each complaint. One complaint can name several.
- Engine127
- Fuel/propulsion system66
- Unknown or other63
- Structure60
- Electrical system50
- Steering23
- Suspension22
- Power train20
- Air bags12
- Visibility10
NHTSA ODI complaints (public domain) · updated 23 Oct 2026 · 7 injuries and 0 deaths reported
Compared with other years
NHTSA ODI complaints by model year
Recalls
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014-2020 C-Class, CLA, GLA, S-Class, GLC, and GLE vehicles. Please refer to MBUSA's recall report for specific vehicle details. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair, allowing the front panel to detach from the vehicle.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2020 C300 Coupe, C43 Coupe AMG, C43 AMG, 2015-2020 C300, GLA250, 2016-2018 C350e, CLA45 Coupe AMG, 2015 C400, S65 AMG, 2015-2019 C63 AMG, 2016 C450, 2015-2016 GLA45 AMG, S600, 2016-2020 GLC300, 2017-2019 GLC43 AMG, GLE43 Coupe AMG, 2014-2019 CLA250 Coupe, 2014-2015 CLA45 AMG, 2018 GLC63 AMG, 2014-2017 S550, 2018-2020 S450, 2016-2019 GLE63 Coupe AMG, 2016 GLE450 Coupe, 2014-2020 S63 AMG, 2018-2019 S560, and 2019 GLC350e vehicles equipped with a panoramic sunroof. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit: https://static.nhtsa.gov/odi/rcl/2019/RMISC-19V787-4620.pdf
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2015-2016 Mercedes Benz C300, 2017-2019 C300 Cabrio, C300 Coupe, C63 Cabrio, 2015 C63S AMG, 2018-2019 C300, C350e, C63 AMG, C63S AMG Cabrio, 2018 C63 AMG Cabrio, C63 AMG Coupe, C63S AMG, C63S AMG Coupe, E300, E400 Cabrio, E400 Coupe, 2019 CLS450, E450 Cabrio, and E450 Coupe rear-wheel drive vehicles. A locknut in the steering rack may break under high load, possibly causing the steering to become stuck in one position.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec, GLK350, GLK350 4Matic, 2016-2017 C350e, C43 AMG, 2015 C400 4Matic, 2016-2018 C63 AMG, GLC300, GLC300 4Matic, 2017-2018 C300 Coupe, C300 4Matic Coupe, C43 AMG, C63 AMG Coupe, C63S AMG Coupe, C300 Cabriolet, C300 4Matic Cabriolet, C43 AMG Cabriolet, C63 AMG Cabriolet, C63S AMG Cabriolet, GLC300 4Matic Coupe, GLC43 AMG, GLC43 AMG Coupe, 2014 E350 Coupe, E350 4Matic Coupe, E350 Cabriolet, E400 Hybrid, 2015-2017 E400 Coupe, E400 4Matic Coupe, E400 Cabriolet, 2014-2017 E550 Coupe, E550 Cabriolet, B250e, 2014-2016 E250 BlueTec, E63 AMG 4Matic Wagon, 2012-2013 E350 BlueTec, 2012-2016 E350, E350 4Matic, 2015-2016 E400, E400 4Matic, 2012 E63 AMG, 2014-2015 E250 4Matic BlueTec, 2013-2016 E350 Wagon, 2017 GLC300d 4Matic, and 2018 GLC350e 4Matic. The driver's air bag may unexpectedly deploy due to insufficient grounding of the steering components if an electrostatic discharge occurs and the air bag clockspring is broken.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550 4Matic vehicles, 2012-2016 E350 vehicles, 2016-2017 GL450 4Matic vehicles, 2012-2014 ML350 4Matic BlueTec vehicles, 2015 S550, S550 4Matic and C300 4Matic Sedan vehicles, 2015-2016 C300 Sedan vehicles, and 2017 SL63 AMG vehicles. Various control units on these vehicles may have been updated with incorrect software, potentially affecting the correct deployment of the air bags in the event of a crash.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2015-2017 C300 4Matic, C300, CLA250, CLA250 4Matic and CLA45 AMG vehicles, 2017 C300 4Matic Cabrio, C300 4Matic Coupe, C300 Cabrio, C300 Coupe, E300, E300 4Matic, E400 4Matic Wagon, E43 AMG 4Matic, GLA250, GLA250 4Matic and GLC300 4Matic Coupe vehicles and 2016 C350e and GLC300 vehicles and 2016-2017 C450 4Matic AMG Sport and GLC300 4Matic vehicles. In the event that the engine or transmission cannot turn over, the starting current limiter may overheat from the repeated attempts of the starter motor attempting to start the vehicle.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2015 C300 and C400 4matic sedans manufactured January 27, 2014, to December 1, 2014. Due to an error in the electric power steering control unit software, the affected vehicles may have a loss of electric power steering assist.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2015 C300 4matic and C400 4matic vehicles manufactured April 7, 2014, to July 25, 2014. In the affected vehicles, the fuel delivery module may be improperly secured to the fuel tank. Secondly, electrical wires that connect to the fuel delivery module might have been pinched between the flange of the fuel delivery module and the tank.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2015 C300 and C400 vehicles manufactured from June 18, 2014, through September 5, 2014, that fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment." The affected vehicles were assembled with horizontal adjustment mechanisms that allow the owner to change the horizontal adjustment used during the manufacturing process, instead of the proper sealing caps.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2015 C300 4Matic and C400 4Matic vehicles manufactured March 28, 2014, to September 18, 2014. If the steering coupling interlock mechanism is not locked in place, the sliding shaft, which is part of the steering column, could become disengaged from the steering coupling socket due to vibrations, steering thrust, or load feedback from the road surface.
Whether a recall was fixed on a particular car is known only to the manufacturer: check the VIN at nhtsa.gov/recalls.
NHTSA recalls · summaries in NHTSA's own words
Service bulletins
What Mercedes-Benz told its dealers about the 2015 Mercedes-Benz C300: known faults, fixes and updates.
| Bulletin | Summary |
|---|---|
| 11010907 | Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes i |
| 11010818 | Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established |
| 11010755 | Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see |
| 11010494 | Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the ve |
| 11009122 | Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer l |
| 11008880 | Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see |
| 11008873 | Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct instal |
| 11008712 | Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connecti |
| 11008323 | Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: O |
| 11008091 | Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protrudin |
| 11008064 | In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles. |
| 11007974 | Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for cor |
| 11007790 | Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside |
| 11007753 | Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an eng |
| 11006658 | Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control |
| 11005294 | Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the ve |
| 11005276 | Complaint Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy Model year 2018 C300 | Model year 2016-2018 GLC300 and E300 | ALL model year SLK/SLC300 and hybrid variants Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is av |
| 11000623 | Complaint Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy Model year 2015-2018 (non-hybrid), and ALL model year 172 and hybrid variants Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for hybrid and model y |
| 11000598 | Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limi |
| 10253722 | Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Model year 2015-2018 Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for model year 2015-2018 vehicles. Model year 2019 Perform software update for N3/10 Engin |
| 10252770 | As previously reported, to enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final app |
| 10248162 | Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material! |
| 10246281 | Fault code P06DA00 is found current or stored in engine control unit. Check engine light may be activated. Various causes Up to Model year 2018 Fault code P06DA00 can be disregarded if not activating the check engine light, unless otherwise specified in the guided test. The vehicle continues to operate as designed. Further causes should be investigated if complaint of check engine light is received. If fault code P06DA00 is activating the check engine light, update software of the ME control unit. No further repairs needed if the code no longer activates check engine light after 2 d |
| 10243565 | In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the intake line assembly on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years / 150,000 miles (whichever occurs first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2015 - 2020 C/E/GLC/SLC and SLK vehicles, under certain circumstances, the partial-load ventilation valve (a part of the intake line |
| 10243308 | Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. Do not perform software update of N3/10 Engine control unit at this time. This LI will be updated once the software solution is available. This LI is in relation to NCU dated |
NHTSA manufacturer communications (public domain)
NHTSA investigations
C300 Wrist-pin allegation
Desiccated Air Bag Inflator Rupture
Front Roof Panel Detachment
NHTSA Office of Defects Investigation