Honda GL1800

The primary drive gear tightening bolt is prone to fatigue failure due to excessive stress from bending forces. When this occurs, the pulse rotor becomes dislodged, leading the ignition signal to fail and causing the engine to stall while driving or fail to st…

The fuel pump impeller may be faulty, which can prevent fuel from being delivered, risking a power cut or engine shutdown. If this happens during driving, it creates a risk of accidents and injuries. The product does not comply with the Regulation on the appro…

Incorrect functioning of the ignition timing control in the engine control unit can cause the engine to stop while driving, increasing the risk of an accident. The product does not comply with the Regulation on the type-approval and market surveillance of two-…

Airbag inflators may degrade over time due to heat and moisture. The inflator body may rupture while activating and metal fragments may pass through the cushion material causing injuries to the rider.

The check valve orifice on the braking system is susceptible to becoming blocked resulting in rear wheel brake dragging. Unexpected braking/dragging increases the risk of a crash and continued riding with the rear brake engaged/dragging may generate enough hea…

Honda (American Honda Motor Co.) is recalling certain 2018-2021 GL1800 Goldwing motorcycles. The primary drive gear bolt on the crankshaft may break, which can result in an engine stall and lock up the rear wheel.

Honda (American Honda Motor Co.) is recalling certain 2018-2024 GL1800 (Goldwing), CBR600RR, and 2018-2019 CBR1000RR motorcycles. The fuel pump impellers may have been improperly molded, which can cause them to deform and result in fuel pump failure.

Honda (American Honda Motor Co) is recalling certain 2020-2022 GL1800 Gold Wing motorcycles equipped with manual transmissions. An ignition timing software error for the engine control unit (ECU) may reduce engine performance, which can result in an engine stall.

Honda (American Honda Motor Co.) is recalling certain 2009-2010 and 2012-2016 Honda GL1800 Gold Wing motorcycles. These motorcycles have air bag inflators assembled as part of the air bag module that may explode due to propellant degradation occurring after long-term exposure to higher absolute humidity, temperature and temperature cycling.

Honda (American Honda Motor Co.) is recalling certain 2006-2009 and 2012 Honda GL1800 (Goldwing) motorcycles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, if not included in "Zone A," Honda is recalling certain 2006-2009 Honda GL1800 (Goldwing) motorcycles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, if not included in Zone A or Zone B above, Honda is recalling certain 2006-2008 Honda GL1800 (Goldwing) motorcycles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Honda (American Honda Motor, Inc.) is recalling certain model year 2006-2010 Honda GL1800 (Gold Wing) motorcycles manufactured February 8, 2006, to May 14, 2009 originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Honda is recalling certain model year 2006-2008 Honda GL 1800 (Gold Wing) motorcycles manufactured May 10, 2007, to May 14, 2009 originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Motorcycles not originally sold or ever registered in either Zones A or B are not subject to this safety recall. These motorcycles are equipped with an air bag inflator assembled as part of the air bag module, used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

American Honda Motor Co., Inc. (Honda) is recalling certain model year 2001-2010 and 2012-2015 GL1800, 2001-2005 GL1800A and 2013-2015 GL1800B motorcycles. The rear brakes of the affected motorcycles may drag after the brakes are released.

HONDA IS RECALLING CERTAIN MODEL YEAR 2001-2010, AND MODEL YEAR 2012 GL1800 GOLDWING MOTORCYCLES. UNDER CERTAIN CONDITIONS, THERE IS A POSSIBILITY THAT THE COMBINED BRAKING SYSTEM'S SECONDARY MASTER CYLINDER MAY CAUSE THE REAR BRAKE TO DRAG.

ON CERTAIN PASSENGER VEHICLES AND MOTORCYCLES, THE OWNER'S MANUALS CONTAIN INCORRECT CONTACT INFORMATION FOR THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S (NHTSA) VEHICLE SAFETY HOTLINE.

ON SOME MOTORCYCLES, CERTAIN FRAME WELDS DO NOT MEET MANUFACTURING SPECIFICATIONS. HIGH LOADS CREATED WHEN RIDING ON ROUGH ROAD SURFACES OR THROUGH POTHOLES CAN CAUSE THE AFFECTED WELDS TO CRACK.

CERTAIN MOTORCYCLES EQUIPPED WITH COMBINED-BRAKE SYSTEMS HAVE A PROPORTIONING CONTROL VALVE (PCV) THAT MECHANICALLY PROPORTIONS BRAKE FORCE WHEN THE REAR BRAKE IS APPLIED. A SEAL IN SOME PCVS IS IMPROPERLY SHAPED, AND BRAKE FLUID LEAKAGE MAY OCCUR.

ON SOME MOTORCYCLES, CERTAIN FRAME WELDS DO NOT MEET MANUFACTURING SPECIFICATIONS. HIGH LOADS CREATED WHEN RIDING ON ROUGH ROAD SURFACES OR THROUGH POTHOLES CAN CAUSE THE AFFECTED WELDS TO CRACK.