Problems owners report
Complaints filed with NHTSA about the 2011 International ProStar, by the system named in each complaint. One complaint can name several.
- Traction control system1
- Service brakes, air1
- Wheels1
- Suspension1
- Vehicle speed control1
- Engine1
NHTSA ODI complaints (public domain) · updated 23 Oct 2026 · 0 injuries and 0 deaths reported
Compared with other years
NHTSA ODI complaints by model year
New York safety inspections
At its first New York inspection the 2011 International ProStar failed the safety check 0.67% of the time — 73% less often than the average 2011 passenger car (2.49%). Median odometer at inspection: 321,216 miles.
NY DMV Vehicle Inspections (vezn-fmmk), initial inspections since Aug 2021 · how we count
Recalls in Canada
15 Transport Canada recalls for the 2011 International ProStar.
| 2023293 18 May 2023 | Lights And Instruments Issue: On certain trucks, the backup lamps could be blocked and may not be visible. As a result, the trucks don't meet the requirements of the Canadian regulat… |
| 2015434 28 Sept 2015 | Structure On certain vehicles, the fifth wheel locking mechanisms could be susceptible to damage and/or wear. This could cause the locking mechanism to fail properly enga… |
| 2015171 22 Apr 2015 | Electrical On certain vehicles, a double battery (24 volt) jump start or electrical load dump could result in an overvoltage condition of the linear power module (LPM) whi… |
| 2014484 30 Oct 2014 | Heater And Defroster On certain vehicles equipped with a no-idle heating, ventilation and air conditioning (HVAC) module, the electrical harness supplying power to the module may no… |
| 2013314 19 Sept 2013 | Accessories On certain trucks equipped with the electronic fifth wheel jaw release system, incorrect air line routing could allow the fifth wheel jaw to release without dri… |
| 2013122 17 Apr 2013 | Structure On certain trucks, the sunshade (an exterior visor mounted above the windshield) may not have been fastened to the cab roof correctly during the manufacturing p… |
| 2012311 19 Sept 2012 | Brakes On certain vehicles, the piston spring brake chamber may have been manufactured incorrectly and could allow air leakage into the chamber. As a result, the park… |
| 2012147 1 May 2012 | Electrical On certain trucks equipped with a MaxxForce 11 or 13 engine, the positive alternator cable may rub against the high pressure power steering hose. Continued con… |
| 2012053 10 Feb 2012 | Brakes On certain vehicles equipped with Bendix ATR-6 Antilock Traction Relay valves, in extremely cold conditions (at or below -18 degrees Celsius), internal ATR valv… |
| 2011302 18 Aug 2011 | Electrical On certain trucks equipped with a MaxxForce 11 or 13 engine, the positive alternator cable may rub against the high pressure power steering hose. Continued con… |
| 2011161 19 Apr 2011 | Brakes Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 121 - Air Brake Systems. The trailer Antilock Brake System (ABS) … |
| 2010455 20 Dec 2010 | Powertrain On certain vehicles, the rubber isolator material that holds the driveline center bearing in the mounting bracket may deteriorate, which could result in driveli… |
| 2010286 26 Aug 2010 | Visual System On certain trucks, the passenger side windshield wiper linkage rod may separate from either the wiper motor drive arm or the passenger side pivot assembly. If … |
| 2010200 11 Jun 2010 | Steering On certain trucks, the fastener that clamps the pitman arm to the steering gear shaft may not have been torqued to specifications during vehicle assembly. This… |
| 2010096 23 Mar 2010 | Electrical On certain vehicles equipped with an optional jump start stud, corrosion at the base of the stud may cause an electrical short between the stud and battery box … |
Transport Canada Vehicle Recalls Database · Contains information licensed under the Open Government Licence – Canada
Recalls
Navistar, Inc. (Navistar) is recalling certain 2000-2003 International 8100, 2001-2003 International 9100i, 2001-2007 International 9400i, 2001-2010 International 9200i, 2002-2007, 2009 International 8500, 2003-2007, 2013 International 9900i, 2003-2018 International 8600, 2004, 2007 International 9900iX, 2008-2018 International ProStar, 2010-2011, 2013, 2016 International LoneStar, 2011-2012, 2016 International 4400, 2017-2024 International LT, 2018-2024 International RH, 2019-2021 International LS, 2019-2024 International MV vehicles. The back-up lights offer low visibility when the vehicle is in reverse and bobtail mode. Also, the vehicles have not been equipped with additional unobstructed back-up lights. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."
Navistar, Inc. (Navistar) is recalling certain model year 2011-2014 International ProStar trucks manufactured May 18, 2010, to April 5, 2013, 2012-2014 International LoneStar trucks manufactured September 7, 2011, to March 25, 2013, and 2011-2013 International TranStar trucks manufactured October 18, 2010, to February 20, 2013. The affected trucks are equipped with Fontaine Ultra LT Fifth Wheel connectors, which, due to cumulative damage to the fifth wheel and its locking mechanism, have a locking mechanism that may fail to operate or to properly engage.
Navistar, Inc. (Navistar) is recalling certain model year 2011-2015 International DuraStar, ProStar, TranStar and WorkStar, 2012-2015 International TerraStar, 2013-2015 International LoneStar and IC Bus HC, and 2014-2015 IC Bus AC vehicles. A vehicle double battery jump start or electrical load dump event could result in an overvoltage condition of a component within the HVAC system linear power module (LPM) which is used to control the blower speed. The overvoltage condition could result in the overheating and failure of the LPM.
Navistar, Inc. (Navistar) is recalling certain model year 2010-2015 International Lonestar vehicles manufactured October 12, 2009, to June 16, 2014, and 2009-2015 International ProStar vehicles manufactured December 16, 2008, to June 20, 2014. In the affected vehicles the electrical harness that supplies power to the HVAC system may not be of sufficient size for the electrical load of the circuit. This can result in an increase in resistance and heating at the connectors.
Navistar, Inc. is recalling certain model year 2008-2013 International LoneStar, ProStar, and TranStar trucks manufactured February 20, 2008, through July 29, 2013 and equipped with an electronic fifth wheel jaw release system (feature code 0595BAW or 0595BAY). Due to an assembly error, the air lines at the isolation/vent valve may not be oriented correctly.
Navistar is recalling certain model year 2011-2012 International Lonestar, model year 2012-2013 International Terrastar and model year 2011-2013 International DuraStar, ProStar, TranStar, and WorkStar commercial trucks manufactured from June 1, 2010, through March 7, 2012 and equipped with day cab codes 16CAB, 16030, or 16196 and feature codes 16WCE, 16WCR, 16XWD, 16XWE, 16XWV, 16XXB, 16XXD, 16XXE, 16XXG, or 16XYN sun shades. The sun shade may not be properly secured to the cab roof panel which may result in partial or full separation of the sun shade from the roof panel.
Navistar is recalling certain model year 2013 International 8600, 2012 and 2013 Durastar, 2011-2013 ProStar, and 2012 WorkStar trucks, manufactured from November 23, 2010, through April 02, 2012, and equipped with piston spring brake feature code 04EVP. The piston bore area of the parking brake chamber may have an air leak could result in the parking brake not fully releasing.
NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2010 THROUGH 2013 PAYSTAR, WORKSTAR, TRANSTAR, AND PROSTAR, AND MODEL YEAR 2012 AND 2013 LONESTAR COMMERCIAL TRUCKS MANUFACTURED FROM JUNE 1, 2009, THROUGH APRIL 4, 2012, EQUIPPED WITH A MAXXFORCE 11 OR 13 ENGINE (FEATURE CODE 12UXJ OR 12UXH) AND WITH BOSCH ALTERNATOR FEATURE CODES 08GGN, 08GGR, 08GHG, OR 08GHH. THE ALTERNATOR CABLE MAY RUB ON THE HIGH PRESSURE POWER STEERING HOSE, POSSIBLY CHAFING ITS INSULATION AND CAUSING AN ELECTRICAL SHORT.
NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2012-2013 IC BUS CE-C, HC, AND INTERNATIONAL 9400 AND CERTAIN MODEL YEAR 2011 THROUGH 2013 INTERNATIONAL DURASTAR, PAYSTAR, WORKSTAR, TRANSTAR, LONESTAR, PROSTAR, 9200, AND 9800, AND CERTAIN MODEL YEAR 2013 INTERNATIONAL 9900, VEHICLES, MANUFACTURED FROM DECEMBER 2, 2010, THROUGH JANUARY 26, 2012, AND EQUIPPED WITH BENDIX ATR-6 TRACTION RELAY VALVES. IN EXTREMELY COLD CONDITIONS, THESE BENDIX RELAY VALVES MAY POTENTIALLY DEVELOP INTERNAL LEAKAGE. INTERNAL LEAKAGE CAN LEAD TO AIR PRESSURE BEING DELIVERED TO AFFECTED PRIMARY OR SECONDARY BRAKES CAUSING CONTINUOUS BRAKE APPLICATION.
NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2010-2012 PAYSTAR, WORKSTAR, TRANSTAR, AND PROSTAR COMMERCIAL TRUCKS MANUFACTURED FROM JUNE 1, 2009, THROUGH MAY 31, 2011, EQUIPPED WITH A MAXXFORCE 11 OR 13 ENGINE (FEATURE CODE 12UXJ OR 12UXH) AND WITH ALTERNATOR FEATURE CODE 08GGN, 08GGR, 08 GHG, OR 08GHH. THE ALTERNATOR CABLE MAY RUB ON THE HIGH PRESSURE POWER STEERING HOSE, POSSIBLY CHAFING ITS INSULATION AND CAUSING AN ELECTRICAL SHORT.
NAVISTAR IS RECALL CERTAIN MODEL YEAR 2011 AND 2012 INTERNATIONAL DURASTAR, PAYSTAR, WORKSTAR, TRANSTAR, LONESTAR AND PROSTAR COMMERCIAL TRUCKS MANUFACTURED FROM NOVEMBER 5, 2010, THROUGH MARCH 10, 2011, FOR FAILING TO COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS (ABS)." THE TRAILER ABS FAULT INDICATOR LAMP IN THE INSTRUMENT CLUSTER WILL NOT ILLUMINATE DUE TO A PROGRAMMING OR HARDWARE ISSUE WITH THE BRAKE SYSTEM ELECTRONIC CONTROL UNIT.
NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2011 INTERNATIONAL PROSTAR COMMERCIAL TRUCKS MANUFACTURED FROM SEPTEMBER 22, 2010, THROUGH DECEMBER 3, 2010, EQUIPPED WITH DRIVELINE FEATURE CODE 06WAK. THE RUBBER ISOLATOR MATERIAL THAT HOLDS THE DRIVELINE CENTER BEARING IN THE MOUNTING BRACKET MAY DETERIORATE DUE TO AN INCORRECT MOUNTING LOCATION POSSIBLY RESULTING IN DRIVELINE SEPARATION WITHOUT WARNING.
NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2008 THROUGH 2011 INTERNATIONAL PROSTAR AND LONESTAR HEAVY TRUCKS MANUFACTURED FROM JANUARY 2, 2007 THROUGH JUNE 1, 2010. THE PASSENGER SIDE WINDSHIELD WIPER LINKAGE ROD MAY SEPARATE FROM EITHER THE WIPER DRIVE ARM OR PASSENGER SIDE PIVOT ASSEMBLY.
NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2010 AND 2011 INTERNATIONAL 4300M, 8600, LONESTAR AND PROSTAR BRAND TRUCKS MANUFACTURED FROM MAY 6, 2009 THROUGH MAY 25, 2010. THE FASTENER THAT CLAMPS THE PITMAN ARM TO THE STEERING GEAR SHAFT MAY HAVE BEEN UNDERTORQUED UPON ASSEMBLY. AN UNDER TORQUE CONDITION MAY CAUSE WEAR OF THE INTERCONNECTING SPLINES OF THE ARM AND THE SHAFT POSSIBLY ALLOWING THE PITMAN ARM TO SLIP OVER THE SHAFT RESULTING IN A REDUCTION OF STEERING CONTROL.
NAVISTAR HAS NOTIFIED NHTSA OF A DEFECT ON CERTAIN MODEL YEAR 2008-2011 INTERNATIONAL TRUCKS EQUIPPED WITH AN OPTIONAL JUMP START STUD. CORROSION AT THE BASE OF THE STUD MAY CAUSE AN ELECTRICAL SHORT BETWEEN THE STUD AND BATTERY BOX.
Whether a recall was fixed on a particular car is known only to the manufacturer: check the VIN at nhtsa.gov/recalls.
NHTSA recalls · summaries in NHTSA's own words
Service bulletins
What International told its dealers about the 2011 International ProStar: known faults, fixes and updates.
| Bulletin | Summary |
|---|---|
| 11010428 | This article addresses chassis lean conditions on all chassis. This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean. |
| 10253979 | This document is to guide users to eliminate brake pedal rattle noise. |
| 10253970 | This document details the procedure that must be followed to ensure proper alternator troubleshooting. |
| 10253960 | This document covers battery diagnostics, maintenance and storage requirement. |
| 10251414 | Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or PSI engine. |
| 10251409 | Suggested alignment target values when performing a vehicle axle alignment. |
| 10246231 | J1939 Data Link Source Address Information |
| 10244926 | Rebuilding Cylinder Heads on Certain MaxxForce 11/13, N13, and A26 engines; 2010 to present. |
| 10243610 | How to request a horsepower quote; all International and Cummins engines |
| 10243596 | General Wheel Speed Sensor Troubleshooting |
| 10243595 | Diagnosis of chassis wander complaints. |
| 10241555 | J1939 Data Link Source Address Information |
| 10241554 | J1939 Data Link Troubleshooting |
| 10240193 | Snap-On torque wrench requirement for all big bore engine connecting rod bolts; A26, MaxxForce 13, N13 engines |
| 10237468 | New air compressor incorporates an oil feed dowel O-ring. Only models equipped with 2010 and newer MaxxForce 11/13 engines, all N13, and A26 engines |
| 10236042 | New Air compressor Incorporates an oil feed dowel O-ring; only models built with MaxxForce 11/13, N13, or A26 Engines |
| 10234021 | Rebuilding cylinder heads on certain EPA 2010 MaxxForce 11/13, N13, and A26 Engines |
| 10234000 | Starter diagnostics and warranty claim procedure for all engines and all chassis EXCLUDING vehicles equipped with PSI engines or Cummins ISB engine with Allison transmissions |
| 10232616 | Rebuilding Cylinder Heads on Certain International MaxxForce 11/13 engines and all International N13 and A26 engines |
| 10227461 | Turbocharger oil supply tube retrofit; only models with 2010 emissions MaxxForce 11 and 13 engines and N13 engines |
| 10227455 | J1939 Data link source address information |
| 10222490 | Pico Scope CCOS (Crankcase Separator Test) |
| 10219330 | PicoScope Test One Channel RCT |
| 10219328 | PicoScope Wheel Speed Sensor Test |
| 10219325 | PicoScope Test Resistance and Ohmmeter |
NHTSA manufacturer communications (public domain)
NHTSA investigations
Leaking MGM brake chambers
NHTSA Office of Defects Investigation